How much concrete do I need for a 15m × 10m slab?

A 15m × 10m slab covers 150 square metres. At 100 mm thick that is 15.00 cubic metres of concrete, or 16.50 once you add the usual ten percent for waste. At 150 mm — the thickness you want if a vehicle will use it — it rises to 22.50 cubic metres, 24.75 with waste. Thickness scales the volume linearly, so half again the depth is half again the concrete.

How many bags of concrete for a 15m × 10m slab?

About 1,500 bags of 25 kg at 100 mm thick, on the basis that a 25 kg bag yields roughly 0.01 cubic metres of finished concrete. That figure alone answers the bags-or-truck question: mixing that many by hand is well beyond a single day of work, and ready-mix will be cheaper as well as faster.

How many ready-mix loads for a 15m × 10m slab?

3 loads at 100 mm thick, assuming an eight cubic metre truck. More than one load means the joint between them matters: either the next truck is on site before the first finishes, or the pour stops at a planned construction joint with reinforcement carried through. A gap long enough for the first concrete to stiffen leaves a cold joint, which is a permanent weak plane.

What is a 15m × 10m slab usually for?

Commercial unit or long yard. That matters for the specification rather than the quantity: the area gives you the concrete, but what sits on the slab decides the thickness, whether it needs reinforcement, and how good the sub-base has to be. Change the thickness on the calculator above to see the volume move — it is the input that costs the most and gets the least thought.

How accurate does the excavation need to be?

More accurate than most people expect, because over-excavation is paid for in concrete. Digging fifty millimetres deeper than intended across a hundred square metres adds five cubic metres of concrete — a whole extra load, filling a hole nobody wanted. It is far cheaper to dig slightly shallow and bring the level up with compacted sub-base than to dig deep and fill the difference with the most expensive material on site.

How thick should a concrete slab be?

A hundred millimetres for a pedestrian floor such as a shed base or garden room, a hundred and fifty where a vehicle will use it, and two hundred or more for lorries, heavy machinery or turning areas. Thickness resists bending, and a slab bends when the ground beneath it is not uniformly supportive — which is why a well-compacted sub-base under a slightly thin slab beats a thick slab on soft ground.

How far apart should control joints be?

No more than about twenty-four times the slab thickness, and with panels kept near square. On a 100 mm slab that gives 2.4 metres; at 150 mm it gives 3.6. The shape rule matters as much as the spacing: a panel much longer than one and a half times its width behaves like a beam and cracks across its middle, so a long slab should be jointed on a grid rather than in strips.

Do I need a damp-proof membrane?

Under anything with a floor people occupy, yes. A concrete slab is not waterproof — moisture wicks up through it by capillary action and appears as damp flooring, lifting adhesive, or condensation on whatever is stored on it. A polythene membrane under the slab stops that. For an outdoor slab such as a patio or yard it is unnecessary, since the surface is exposed anyway and trapped moisture has nowhere useful to go.

How much sub-base does a slab need?

A hundred millimetres of compacted granular material under a domestic slab, a hundred and fifty under anything carrying vehicles, and more on soft or made-up ground. Order it by the loose volume rather than the finished depth, because crushed stone settles by roughly a quarter as it compacts. Compact it in layers of no more than a hundred millimetres — a single deep dump never consolidates properly and the slab settles into the soft spots later.

Concrete for a 15m × 10m Slab

Fifteen by ten is the first rectangle on this list rather than a square, and the shape matters as much as the area. A hundred and fifty square metres in a long thin rectangle behaves differently from the same area in a square: the long dimension carries more thermal movement, the joint layout has to reflect it, and the...

SLAB DIMENSIONS

LENGTH (metres)

WIDTH (metres)

THICKNESS (millimetres)

CONCRETE PRICE ($/m³, optional)

Enter your local ready-mix price for an estimate.

RESULTS

VOLUME (exact)

15.00 m³

WITH 10% WASTE — order this amount

16.50 m³

25 KG BAGS

1500

≈ 0.01 m³ per 25 kg bag

ESTIMATED MATERIAL COST

$2,475

at $150/m³ + 10% waste

SLAB VISUALISER (not to scale)

SLAB SUMMARY

Surface area150.00 m²

Thickness100 mm

Volume exact15.0000 m³

Volume +10%16.5000 m³

25 kg bags1500 bags

THICKNESS GUIDE

75mm

Paths, light paving

Foot traffic

100mm

Patios, residential slabs

Standard residential

150mm

Driveways, garage floors

Vehicles

200mm

Commercial floors

Heavy loads

UNIT CONVERSIONS

1 cubic yard = 27 cubic feet

1 cubic yard ≈ 0.765 m³

80 lb bag ≈ 0.6 cubic feet

60 lb bag ≈ 0.45 cubic feet

25 kg bag ≈ 0.01 m³

Always order 10% extra for waste

Created with❤️byeaglecalculator.com

HOW TO USE

1
The calculator opens with 15 by 10 metres already entered. Adjust the thickness to match what the slab will carry — 100 mm for a pedestrian floor, 150 mm where a vehicle will use it.
2
Read the volume with and without the ten percent waste allowance. Order the figure with waste included; the exact figure is there so you can see how much of the order is margin.
3
Compare the bag count against the ready-mix load count. At 15.00 cubic metres this is past the point where bags make sense on cost or effort.
4
Switch to imperial with the unit toggle if you are working in feet and inches, or change the dimensions if your slab is not exactly 15m × 10m.

WORKED EXAMPLE

A 15m × 10m slab at 100 mm thick. The area is 15 × 10 = 150 m². Multiplying by the 0.1 m thickness gives 15.00 m³ of concrete. Adding ten percent for waste — for an uneven sub-base, spillage, and the last of the load left in the chute — brings the order quantity to 16.50 m³. That is about 39.6 tonnes. In 25 kg bags, at roughly 0.01 m³ of finished concrete per bag, that is 1,500 bags. From a truck holding 8 m³ it is 3 loads. At 150 mm instead, the same area needs 22.50 m³, or 24.75 m³ with waste — half again the concrete for half again the depth.

FREQUENTLY ASKED QUESTIONS

RELATED CALCULATORS

Concrete for 10m × 10m Slab Calculator

Calculate instantly →

Concrete for 12m × 12m Slab Calculator

Calculate instantly →

Concrete Steps Calculator

Calculate instantly →

Concrete for 4m × 4m Slab Calculator

Calculate instantly →

MORE CONCRETE CALCULATORS

Concrete Slab Volume Calculator

Calculate instantly →

Concrete Footing Volume Calculator

Calculate instantly →

Concrete Bags Calculator

Calculate instantly →

Concrete Patio Calculator

Calculate instantly →

Concrete Driveway Calculator

Calculate instantly →

Concrete Mix Ratio Calculator

Calculate instantly →

Post Hole Concrete Calculator

Calculate instantly →

Concrete Steps Calculator

Calculate instantly →

Rebar Quantity Calculator

Calculate instantly →

Cement Render Calculator

Calculate instantly →

Ready-Mix Concrete Cost Calculator

Calculate instantly →

Concrete Wall Volume Calculator

Calculate instantly →

Concrete Path Calculator

Calculate instantly →

Pool Deck Concrete Calculator

Calculate instantly →

Concrete for 3m × 3m Slab Calculator

Calculate instantly →

Concrete for 4m × 4m Slab Calculator

Calculate instantly →

Concrete for 5m × 5m Slab Calculator

Calculate instantly →

Concrete for 6m × 6m Slab Calculator

Calculate instantly →

Concrete for 8m × 8m Slab Calculator

Calculate instantly →

Concrete for 10m × 10m Slab Calculator

Calculate instantly →

Was this calculator helpful?

Last updated: July 28, 2026 · Formula verified by EagleCalculator team · Eagle-eyed accuracy for every calculation.